I. Introduction 1. Introduction; 2. Fundamental Knowledge about Basic Process; 3. Process Parameters and Ranges II. Main Equipment 1. Overview of Types, Functions, and Description of Main Equipment; 2. Steam Generator: Boiler; 3.
Turbine Types; 4. Generator; 5. Boiler Feed Pump and Condensate Extraction Pump with Associated Measurements; 6. Deaerators and Heaters; 7. Function and Description of CW and ACW Systems; 8. Demineralizing Plant''s Function and Description; 9. Basic System Functions and Description of Coal Handling; 10. Basic System Functions and Description of ASH Handling III.
Plant P&ID Discussions 1. Introduction (P&ID); 2. Main Steam (P&ID); 3. Reheat Steam (P&IDs): Cold and Hot Reheat; 4. Extraction Steam (P&IDs): Bleed Steam; 5. Auxiliary Steam (P&IDs); 6. Feed Water System (P&ID); 7. Condensate System (P&IDs); 8.
Heater Drain and Vent (P&IDs); 9. Air and Flue Gas System (P&IDs); 10. Cogeneration P&ID; 11. Miscellaneous Other Systems (P&ID) IV. General Instruments 1. Introduction; 2. Pressure Measurement: Various Measuring Points and Range Selection; 3. Temperature Measurement: Various Measuring Points and Range Selection; 4.
Flow Measurement, Various Measuring Points, Various Types, and Range Selection; 5. Level Measurement V. Special Instrument 1. Special Instruments; 2. Vibration and Turbovisory Instruments; 3. Gas Analyzers; 4. Steam and Water Analysis System; 5. Sample Conditioning System; 6.
Blow Down and Dosing Control; 7. Analyzers for Air Pollution Monitoring and Control (NOX Control) VI. Final Control Element 1. Valves and Actuators; 2. Control Valve Types; 3. Dampers and Miscellaneous other FCEs; 4. Actuators; 5. Accessories VII.
Intelligent Control System 1. Basics (Discussion on Intelligent Network System); 2. PLC System: Introduction; 3. Annunciation and Sequence of Events: Preamble; 4. Integrated DCS-DDC MIS: Preamble; 5. MMI and Recording: Introduction; 6. MIS: Introduction VIII. Boiler Control System 1.
Basic Control Requirements; 2. Steam Pressure Control with Load Index; 3. Air Flow Control; 4. Fuel Flow Control; 5. Coal Mill Control--Mill Air Flow for TT Boiler; 6. Furnace Draft Control; 7. Drum-Level and Feedwater Controls; 8. Superheater Temperature Control; 9.
Reheat Temperature Control; 10. Miscellaneous Boiler Controls, including Overfire Air Dampers; 11. HP-LP Bypass System; 12. Boiler OLCS: Introduction to Interlock and Protection of Boiler BMS, SADC, and SB Control IX. Turbo Generator Control System 1. Introduction; 2. Electro Hydraulic Governor Control System; 3. Turbine Protection System; 4.
ATRS; 5. ATT System; 6. Thermal Stress Evaluator; 7. LPBP System; 8. Turbine Controls: Seal Steam Pressure Control System; 9. Hydrogen Seal Oil System and Differential Pressure Control; 10. Generator Control System; 11. Condenser Level and Deaerator Level Control System; 12.
Various TG Options and Miscellaneous TG Controls X. Coordinated Control System 1. Introduction; 2. Coordinate Control Mode; 3. Turbine Follow Mode; 4. Boiler Follow Mode; 5. Run Back System; 6. Discussions and Explanations XI.
Balance of Plant Control System 1. Balance of Plant: Introduction; 2. BFP Recirculation Control; 3. CEP Recirculation Control; 4. GSC Minimum Flow Control; 5. Deaerator (Pressure) Control; 6. LP Heater Level Control; 7. HP Heater Level Control; 8.
Ejector Control and TAS XII. Installation Practices 1. Introduction; 2. Pipe Valve Fitting Material Specification and Rating; 3. Mechanical Installation of Instruments; 4. Electrical Installation of Instruments XIII: Advanced Ultra-Supercritical Thermal Power Plant and Associated Auxiliaries XIV: Plant safety life cycle and Safety Integrated level Appendix I. Process and Mechanical Standard Table; II. Electrical Data and Tables; III.
ISA Standard, Materials, Human Engineering, and Control Room; IV. Network Control and Communication; V. Super/Ultra Super Critical Power Plants; VI. Integrated Gasifier and Combined Cycle Plant (Pollution Control); VII. A Few Operational Features of the Unit.